h1

Menggunakan Packet Tracer

Desember 7, 2009

Packet tracert  adalah software simulasi jaringan, jadi sebelum mengkonfigurasi di router asli lebih baik belajar konfigurasiny di packet tracert.  sintak yang dipake nya juga gak beda koq jika kita ingin konfigurasi di router asli.

aku udah nyoba konfigurasi di router asli..

tapi masi pake yang konfigurasi router statis..

cuma sekedar berbagi ilmu aja…

Baru-baru ini aku baru belajar konfigurasi Router Dinamik di packet tracert menggunakan RIP versi 1 dan Versi 2

perbedaan RIP versi 1 dan RIP versi 2 adalah pada pemakaian host nya. jika menggunakan RIP versi 2 penggunaan host lebih efisien, karena host yang ada dipakai sesuai keperluan.

pertama bukalah software packet tracert

kemudian buatlah Rangkaian network seperti ini :

Rangkaian ini hanya fiktif… Hanya Sekedar Pembelajaran setting Jaringan

isi command line dari Router_Lampung :

RouterLampung(config)#interface serial 0/0/0
RouterLampung(config-if)#ip address 192.168.2..
^
% Invalid input detected at ‘^’ marker.
RouterLampung(config-if)#ip address 192.168.2.1 255.255.255.252
RouterLampung(config-if)#clockrate 64000
^
% Invalid input detected at ‘^’ marker.
RouterLampung(config-if)#clock rate 64000
RouterLampung(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
RouterLampung(config-if)#interface serial 0/0/1
RouterLampung(config-if)#ip address 192.168.4.1 255.255.255.252
RouterLampung(config-if)#
RouterLampung(config-if)#clock rate 64000
RouterLampung(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
RouterLampung(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterLampung#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterLampung(config)#interface fa
RouterLampung(config)#interface fastEthernet 0/0
RouterLampung(config-if)#ip address 192.168.3.1 255.255.255.192
RouterLampung(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterLampung(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterLampung#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterLampung(config)#rrouter rip
^
% Invalid input detected at ‘^’ marker.
RouterLampung(config)#router rip
RouterLampung(config-router)#version 2
RouterLampung(config-router)#network 192.168.3.0
RouterLampung(config-router)#network 192.168.2.0
RouterLampung(config-router)#network 192.168.4.0
RouterLampung(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
isi command line Router Jakarta

RouterJakarta(config-if)#ip address 192.168.4.2 255.255.255.252
RouterJakarta(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
RouterJakarta(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
RouterJakarta(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterJakarta#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterJakarta(config)#interface fa
RouterJakarta(config)#interface fastEthernet 0/0
RouterJakarta(config-if)#ip address 192.168.10.1 255.255.255.0
RouterJakarta(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterJakarta(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterJakarta#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterJakarta(config)#router rip
RouterJakarta(config-router)#version 2
RouterJakarta(config-router)#network 192.168.4.0
RouterJakarta(config-router)#network 192.168.10.0
RouterJakarta(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
isi command Line Router Palembang

RouterPalemabeng(config)#interface serial 0/0/0
RouterPalemabeng(config-if)#ip address 192.168.2.2 255.255.255.252
RouterPalemabeng(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
RouterPalemabeng(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
RouterPalemabeng(config-if)#interface fa
RouterPalemabeng(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterPalemabeng#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterPalemabeng#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterPalemabeng(config)#interface fa
RouterPalemabeng(config)#interface fastEthernet 0/0
RouterPalemabeng(config-if)#ip address 192.168.20.1 255.255.255.240
RouterPalemabeng(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterPalemabeng(config-if)#exit
RouterPalemabeng(config)#router rip
RouterPalemabe(config-router)#version 2
RouterPalemabe(config-router)#network 192.168.2.0
RouterPalemabe(config-router)#network 192.168.20.0
RouterPalemabe(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterPalemabeng#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
Iklan

2 komentar

  1. yaakk ampunn jenggg
    banyakk ee… hahahhaha

    rajinn matiii nian budak jarkom


    • hhhaaa…

      iya… =))
      tag papela nova..
      klo Xan Lupa kan bisa liat di blog aquh..^ ^



Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s

%d blogger menyukai ini: